FGTECH Galletto 4 V54 read write VAG BMW ECU what tested OK?

Which VAG BMW ECU types are tested OK to read write by FGTECH Galletto 4V54? Here is a list to show you all tested OK results!

FGTECH V54 read write BMW EDC15 EDC16 EDC17 success:

BMW 330d EDC15C4 read ok/write ok via OBD

BMW e46 2.0D EDC16c31- ok

BMW E90 2.0D EDC16c35- ok

BMW E70 3.0D EDC16 (BDM)

BMW 3/5/7 series

EDC16C31/35 OBD r/w ok

EDC17 in boot mode ok

BMW E87 116D 2.0 EDC17C06 boot mode r/w ok

BMW E83 3.0d ODB r/w ok

BMW X6 3.0D 2012 and 2013 (306 and 245hp) BOSCH EDC17CP45 read/write BOOT ok

BMW E90 EDC17CP reading ok, boot mode ok

EDC16 OBD

EDC16C31 OBD

BMW X5 2007 3.0TDI

BMW 525 (E39)

BMW 320D E46

BMW E90

FGTECH V54 read write VAG EDC16 EDC17 PCR2.1 MED9.1 success:

EDC16U34 (VAG) Read/Write ok (OBD)

EDC16U1 (VAG) Read/Write ok (OBD)

MED9.1 (VAG) Read/Write ok (ODB)

Trionic8 (SAAB 9-3) READ/WRITE OK (OBD)

EDC16P (VAG) Read/Write ok (OBD)

EDC15V (VAG) Read/Write ok (OBD)

EDC17CP14 03L906022G Read/Write ok (OBD and boot mode)

AUDI ME 7.1.1 3.0 v6 read ok

EDC16 OBD r/w generally ok

EDC17 in boot mode ok

MED17.5.1 Boot mode r/w ok

AUDI Q7 3.0tdi BDM ok

VAG EDC16CP34 OBD read/write ok

VAG PCR2.1 read/write OBD ok, PCR2.1 unlock via boot mode ok

Get FGTECH Galletto 4 V54 only €56.99 here!

http://www.eobdtool.co.uk/wholesale/fgtech-galletto-4-master-ecu-programmer.html

How Fgtech Galletto 4 V54 read write flash ECU EDC16c34 via OBD?

This blog will offer you a guide for how use Fgtech Galletto 4 V54 to read and write ECU EDC16c34 via OBD. (Not on bench) Check below steps!

Engine: 1.6 HDi Berlingo
ECU Type: EDC16C43

ECU BOSCH number: 0281012619, year 07-12-05, 9663943980

Action: Fgtech read write EDC16C43 via OBD

How Fgtech Galletto 4 read EDC16c34 via OBD?

Step1. Connect Fgtech Galletto 4 V54 Master directly to car OBD port then connect it to laptop via USB cable. (When read ECU you don't need 12v external power supply)

Turn on the key to position 1 but don't start engine.

Step2. Open Fgtech V54 software, first click “Select Driver” to choose correct driver for your car / ECU.

Next check “ECU Data” to see if connection is OK.

Step3. Click “Read file”, enter name of the file, and reading start.

Wait until reading is 100% complete. Turn the dashboard off.

How FgtechGalletto 4 write EDC16c34 via OBD?

NOTE:

1.     Make sure your car battery is ok. You must have over 12v steady volts to write. You can connect your car battery to external 12v charger.

2.     You can damage your ECU if voltage drops under 12v. If writing process is disrupted you can recover your ECU only by BDM restore.

Click “Write file” to start ECU writing.

When the writing complete, turn off the dashboard and wait 3 minutes.

Then turn on dashboard and wait 3 minutes. After that you can turn on the engine.

(Solved) Audi A4 1.8T 2007 Car not start after reading

Car model and year:

Audi A4 1.8T 2007 163hp

Tool to use:

Fgtech Galletto v54

I read this with Fgtech Galletto v54 with OBD-

1.8 Turbo 150/180CV ME7.5.1 29f400BB..galletto say change driver

1.8/2.0 Turbo 150/180CV ME7.5.5 29f800BB....read success...100% Ignition off...

Symptoms:

Will write the remap....he wants to drive off...car not start

VCDS go ECU an read fault code say "programming process not finished"

I have just read, not write...

100% working solution:

The car is running

What I did as follows:

-> I remove fuses from Dash and Radio\Navi

-> use a good bosch powersupply (14V)

-> delet all fault code VCDS

-> write the same file was read before with Fgtech Galletto

-> note all prompts from galletto about ingnition on/off

-> car start....running

-> delet all fault code VCDS

Best Quality FGTech V54 Galletto 4 Master

Which EDC17 Reader works well for a good price?

BDM100, FGTECH 54, MPPS v16, kess v2.06 or any other tools/ solution is optional? 

Let’s hear from some experienced ECU tunners.

• For EDC16 iam using BDM100 from china.
• I USE FGTECH 54 AND IS OK. no problem.
• I read one EDC17 in Audi A4 with MPPS v16.
• Another EDC17 I read in boot mode with galletto v54 good china clone... Do job perfectly.

When you have problem, just try this way: uninstall all fgtech software. Install basic version. Connect tool and give drivers. Unplug tool. Remove basic. Install Win7 version. Plug tool + drivers. Done.

• I use the kess v2.06 reworked pcb and fw updated, like 08 what is available...is great tool, recently KESS FM V4.036 available, haven’t test it, but I think it will do. As told by eobd2.fr customer service, the older fw kess v2 is available to update firmware by returning back the main unit to them and charge $89, but the QC number has to be ended with 015.
• I use byteshooter does most ecus obd2, inclusively edc17 first models until 2009, first generation. For late edc17 byteshooter reads very good on table, only resistor adding is needed. If you want good tool go Byteshoter. Never had issues with it. Galetto v54 reworked pcb works good too.
• CMD CAN Flasher dont can read write all edc17 by obd, only a few.

Flash VAG Bosch EDC16U34 ECU with FGTech Galletto 4

FGTech V54 Galletto 4 is the fastest and most secure chip tuning tool, features Multi-language, User-friendly and No Activation Needed. FGTech V54 supports wide range of vehicles, such as truck, motorcycles, cars and marine.

Supported OS: A laptop running Win XP / Vista / Win7 (without any anti-virus software and internet/network connection)

Guide for you to flash VAG Bosch EDC16U34 ECU:

1. Install the V54 FGTech Galletto 4 Master Software;

Video for Installation Reference: https://www.youtube.com/watch?v=FH_V39N3FlM

2. Connect v54 fgtech galletto 4 master with PC/Laptop, setup boot and BDM.

3. Find out the BDM pads showed at following picture;

4. Carefully align with the BDM Port ECU programming spring adapter/probe drop and secure frame.

Kindly Note: Confirm all is connected correctly;

5. Run FGTech V54 software, accept the system notice.

Kindly Note:

Make sure you have 12V+ feeding FGTECH 4 master main device and the intermediate adapter.

6. Turn intermediate adapter to ON, the read LED indicator will flash;

7. Click the Option list as the order: “Select Driver” >> “BMD-Jtag” >> “Connect”;

8. If communication between FGTech Galletto 4-Master V54 and PC/Laptop is well built, green bar will start loading and finally display ECU information.

9. Ready to read and write ECU. Choose “Read EEPROM” to read EEPROM via system prompts, and then select “Write Eeprom”; once ok, turn the switch off.

10. Exit FGTech V54 software program.

Pro technician experience with Chinese fgtech V54 Galletto 4

2nd March, 2015 update

I just bought Chinese 2014 FGTech V54 Galletto 4 at €67.88 + shipping to US, so I will test it once I get it next week and advise.

7th March, 2015 update

I just received my package today. I will install and test tomorrow and advise how it goes.

8th march, 2015 update

Enclosed are 2 images of galletto v54, I don´t know if there is a difference with version 53.

In the beginning, as for the software I am having some trouble installing it cause there is only 2 files. It installs ok but when try to run I can’t do it. I am working on it. Finally, I have installed the software, actually it was pretty simple to install. First install galletto app, the install galletto win7 app that is it. If anyone have issue to install fgtech v54 software, follow this video: https://www.youtube.com/watch?v=FH_V39N3FlM

9th march, 2015 update

I tried to test with car and test successfully on these models:

continental simos pcr 2.1 unlock and read/write via obd

edc17cp20 read/write boot mode

edc16c34 read/write bdm

med 9.5.10 read/write bdm

t5 2008 edc16.... read/write bdm

me7.1 obd and pinout need immo off

edc15p read/write pinout need to set power to max. mode not eco mode from power settings . if power set to eco mode will not even read it

t4 edc15vm read/write pinout most chose from car list LT not t4

Conclusion:

I see a lot of users have Galetto 4 v54 error on writing mitsu mh7203 mcu , mine is working good until today , just after I installed the FNR 4 in 1 galleto refused to work I did everything , uninstall/installed drivers exct......

Long story to short: Fgtech Galleto V54 likes it to be single (like VASPC and BMW on same partition (for some)

I don’t know but maybe it is a good idea also to have a look at what soft is installed together with it just a thought as I bumped into this problem today only way I could solve was to reformat.

IMMO off FIAT Punto with v54 fgtech galletto 4 master

Need to immo off FIAT Punto, and I need to know what chip that I should read???

The following photo shows the ECU that I need to immo off.

Someone told me that I can read it by BDM100 or PIASINI.

Someone guest me I have a me73h4 ECU. I can read it many ways.

Here is a diagram how to read flash he made, he use galleto v54 for it. It always works well.

Then I ordered one v54 fgtech galletto 4 master, use your galetto on car list

pin 20 = gnd

pin 51.49.33.17.18 = +12 v

pin 53 = kline ( green wire in galletto)

I can read fiat me7.3 as ferrari me7.3 or alfa me7.3 by using ME 73H4. but this ECU is for fiat and it is not on the car driver list of fgtech galletto v54,according to galletto list, the fiat punto 1.2 16v is not on the list . there is just the photo of the ECU. I have to select the car and model so i can read. and there is no other car that has the same ECU .