(Solved) Audi A4 1.8T 2007 Car not start after reading

Car model and year:

Audi A4 1.8T 2007 163hp

Tool to use:

Fgtech Galletto v54

I read this with Fgtech Galletto v54 with OBD-

1.8 Turbo 150/180CV ME7.5.1 29f400BB..galletto say change driver

1.8/2.0 Turbo 150/180CV ME7.5.5 29f800BB....read success...100% Ignition off...

Symptoms:

Will write the remap....he wants to drive off...car not start

VCDS go ECU an read fault code say "programming process not finished"

I have just read, not write...

100% working solution:

The car is running

What I did as follows:

-> I remove fuses from Dash and Radio\Navi

-> use a good bosch powersupply (14V)

-> delet all fault code VCDS

-> write the same file was read before with Fgtech Galletto

-> note all prompts from galletto about ingnition on/off

-> car start....running

-> delet all fault code VCDS

Best Quality FGTech V54 Galletto 4 Master

Which EDC17 Reader works well for a good price?

BDM100, FGTECH 54, MPPS v16, kess v2.06 or any other tools/ solution is optional? 

Let’s hear from some experienced ECU tunners.

• For EDC16 iam using BDM100 from china.
• I USE FGTECH 54 AND IS OK. no problem.
• I read one EDC17 in Audi A4 with MPPS v16.
• Another EDC17 I read in boot mode with galletto v54 good china clone... Do job perfectly.

When you have problem, just try this way: uninstall all fgtech software. Install basic version. Connect tool and give drivers. Unplug tool. Remove basic. Install Win7 version. Plug tool + drivers. Done.

• I use the kess v2.06 reworked pcb and fw updated, like 08 what is available...is great tool, recently KESS FM V4.036 available, haven’t test it, but I think it will do. As told by eobd2.fr customer service, the older fw kess v2 is available to update firmware by returning back the main unit to them and charge $89, but the QC number has to be ended with 015.
• I use byteshooter does most ecus obd2, inclusively edc17 first models until 2009, first generation. For late edc17 byteshooter reads very good on table, only resistor adding is needed. If you want good tool go Byteshoter. Never had issues with it. Galetto v54 reworked pcb works good too.
• CMD CAN Flasher dont can read write all edc17 by obd, only a few.

Flash VAG Bosch EDC16U34 ECU with FGTech Galletto 4

FGTech V54 Galletto 4 is the fastest and most secure chip tuning tool, features Multi-language, User-friendly and No Activation Needed. FGTech V54 supports wide range of vehicles, such as truck, motorcycles, cars and marine.

Supported OS: A laptop running Win XP / Vista / Win7 (without any anti-virus software and internet/network connection)

Guide for you to flash VAG Bosch EDC16U34 ECU:

1. Install the V54 FGTech Galletto 4 Master Software;

Video for Installation Reference: https://www.youtube.com/watch?v=FH_V39N3FlM

2. Connect v54 fgtech galletto 4 master with PC/Laptop, setup boot and BDM.

3. Find out the BDM pads showed at following picture;

4. Carefully align with the BDM Port ECU programming spring adapter/probe drop and secure frame.

Kindly Note: Confirm all is connected correctly;

5. Run FGTech V54 software, accept the system notice.

Kindly Note:

Make sure you have 12V+ feeding FGTECH 4 master main device and the intermediate adapter.

6. Turn intermediate adapter to ON, the read LED indicator will flash;

7. Click the Option list as the order: “Select Driver” >> “BMD-Jtag” >> “Connect”;

8. If communication between FGTech Galletto 4-Master V54 and PC/Laptop is well built, green bar will start loading and finally display ECU information.

9. Ready to read and write ECU. Choose “Read EEPROM” to read EEPROM via system prompts, and then select “Write Eeprom”; once ok, turn the switch off.

10. Exit FGTech V54 software program.

Pro technician experience with Chinese fgtech V54 Galletto 4

2nd March, 2015 update

I just bought Chinese 2014 FGTech V54 Galletto 4 at €67.88 + shipping to US, so I will test it once I get it next week and advise.

7th March, 2015 update

I just received my package today. I will install and test tomorrow and advise how it goes.

8th march, 2015 update

Enclosed are 2 images of galletto v54, I don´t know if there is a difference with version 53.

In the beginning, as for the software I am having some trouble installing it cause there is only 2 files. It installs ok but when try to run I can’t do it. I am working on it. Finally, I have installed the software, actually it was pretty simple to install. First install galletto app, the install galletto win7 app that is it. If anyone have issue to install fgtech v54 software, follow this video: https://www.youtube.com/watch?v=FH_V39N3FlM

9th march, 2015 update

I tried to test with car and test successfully on these models:

continental simos pcr 2.1 unlock and read/write via obd

edc17cp20 read/write boot mode

edc16c34 read/write bdm

med 9.5.10 read/write bdm

t5 2008 edc16.... read/write bdm

me7.1 obd and pinout need immo off

edc15p read/write pinout need to set power to max. mode not eco mode from power settings . if power set to eco mode will not even read it

t4 edc15vm read/write pinout most chose from car list LT not t4

Conclusion:

I see a lot of users have Galetto 4 v54 error on writing mitsu mh7203 mcu , mine is working good until today , just after I installed the FNR 4 in 1 galleto refused to work I did everything , uninstall/installed drivers exct......

Long story to short: Fgtech Galleto V54 likes it to be single (like VASPC and BMW on same partition (for some)

I don’t know but maybe it is a good idea also to have a look at what soft is installed together with it just a thought as I bumped into this problem today only way I could solve was to reformat.

IMMO off FIAT Punto with v54 fgtech galletto 4 master

Need to immo off FIAT Punto, and I need to know what chip that I should read???

The following photo shows the ECU that I need to immo off.

Someone told me that I can read it by BDM100 or PIASINI.

Someone guest me I have a me73h4 ECU. I can read it many ways.

Here is a diagram how to read flash he made, he use galleto v54 for it. It always works well.

Then I ordered one v54 fgtech galletto 4 master, use your galetto on car list

pin 20 = gnd

pin 51.49.33.17.18 = +12 v

pin 53 = kline ( green wire in galletto)

I can read fiat me7.3 as ferrari me7.3 or alfa me7.3 by using ME 73H4. but this ECU is for fiat and it is not on the car driver list of fgtech galletto v54,according to galletto list, the fiat punto 1.2 16v is not on the list . there is just the photo of the ECU. I have to select the car and model so i can read. and there is no other car that has the same ECU .

How to use Fgtech galletto 4 V54 ECU Programmer？

BDM Alternative - Galletto setup - a how to

However, from time to time I see members still asking how to do a bench setup, so I thought I'd quickly throw something together (hence the carpet!! Don't do this!!!) And show how you can bench/carpet flash via BDM (I am partial to BDM still despite the OBD advancement).

Alternative to this is of course the very excellent XDFproject Tool made by forum member Tap (there's no need to do a write up on this as Tap provides a how-to when you buy his tool).

Let me say that Tap's tool is in my opinion superior for the general user (as it reads both chip sets at the same time (rather than individually like the Galletto clone) and is a faster working system and has potential for future upgrades - it also has various debug modes built into it).

Anyways, if you are after a cheapish BDM solution a clone Fgtech V54 is the way to go and it works well.

Once you have installed everything correctly and the software runs, hook your system up like so (one power supply source to power the DME and Fgtech v54 Galletto 4 is sufficient, in this case a switchable power supply pack that's on 12V 2.5A output was stable for this DME [Edit: my subsequent testing has shown that 2.5A might be insufficient for this DME - I still feel it needs to be 5-10A to be stable).

Software screen should show you the voltage, select 5V for BDM flashing.

Galletto provides a connector board between the Galletto 4 v54 main unit and the BDM connector plug line - this basically just switches the pins around. I didn't like the board itself as it made everything too short and the contacts were not insulated so you could accidentally ground or short on the DME, so ended up making my own conversion harness (easily enough to do, just follow the printed track on the connector board) - Self made harness top, supplied board bottom.

The siemens BDM connector

Alternatively you can use spring loaded BDM probes on a siemens board that you can buy on the net - handy if you don't want to solder header pins.

From main software screen select driver and select as per screenshot for the MSS54/HP

Ok, then click Connect

Once connected, it will show the chipset in box on top left. In this case FLASH AMD 29F200BB

Now to read, click Read Ext Flash, screen pops up, just type in name of the file you want to call it and the location you want to save it to

Save and it'll start reading

Done.

To write, the process is the same, except you select Write Ext Flash. A screen will pop up for you to select the .bin file. Then it'll ask if you want checksum corrected. Rest is self explanatory.

FAQ FgTech Galletto 4 V54 mini ECU master

Following are the most frequently asked questions of FgTech Galletto V54 ECU tuning kit Master version.

About software:

Q: I have got my package, but the CD is broken, where and how can i get the software? 

A: Sorry, you need to buy new FgTech ECU programmer.

Q: After I install the software, it ask me to update it, can I update it?
A: No, update the Galletto V54 software will damage the device.

Q: Is it possible to download the key tools software because CD is corrupted?

A: Here is the link for mini tag key tool software:
http://www.chinaautodiag.com/html/tag-key-tool-software-free-download-457.html

Q: Is there manual to install galletto because i don't have information?

A: Here is the software installation video guide for FGTech Galletto 4:

https://www.youtube.com/watch?v=R0gpO0wAxZw

About function:

Q: FGTech Galletto 4 can cancel EGR gestation via OBD? 

A: Sorry, at present it still can not do this function, it just can read and write the Data of Engine ECU

Q: Can Fgtech V54 do this ecu Bosch EDC16 BMW(P3)?

A: Yes, it can do.

Q:Can your v54 master really can do boot mode tricore?
A:Yes,it can do,but depends on your ecu ,sir,we have tested on VW,it can do

Q: Hello I wanted to know if it can work with the truck to 24v or needs transformer

A: Sorry, Galletto V54 cannot support 24V truck model.

Q: Hello new V54 FGtech Galletto 4 support NEW JTAG Renesas?

A: It can support new chip JTAG, but can not support all of these ecu chips. Please kindly note.

Q: Hello, does FG-tech V54 can support Peugeot 308Turbo?

A: Whether it work on your car, that's mainly depends on the ecu model, please check fgtech v54 ecu passing list here:

http://www.eobdtoolshop.co.uk/upload/service/fgtech-galletto-v54-ecu-passing-test(06-16-2015-update).pdf

Q: Does FGTech Galletto Support Siemens Sid 208 OBD or Tricore? 

A:  FGTech Galletto supports Tricore function.

Q:Can FGTech Galletto work in Continental SID 208?

A: Sorry, it cannot.

Q: Can fgtech v54 supports checksum function?

A: Yes, fgtech v54 can checksum automatically after it read out the data.

Q: Will fgtech galletto 4 V54 master work on 2007 Dodge Caravan J1850 protocol?

A: Yes, you can try it.

Q: Fg tech v54 can read and write the edc17c9 Opel fiat?

A: Sorry, it cannot.

Q: For MED 17,which one is better, KESS V2 or this one?

A: KESS V2 is better.

Q: Install well,test well,just wonder why it cannot do 2013 or 2014 years car

A: This version just can do 2013 around, cannot do very new car

 About installation:

Q: I installed the Galetto V54 Software and Driver on my Windows XP without any Problems. Then I tried to start the Software. I get the error "This Software cannot run under Virtual Machine". 

A: Try opening the VMX file associated with the virtual machine.

Add these lines:

monitor_control.restrict_backdoor = "TRUE"
disable_acceleration = "TRUE"

Q: Can I install FgTech Galletto V54 software on Win 7?

A: Yes, but you can load Galletto software on one system only, Win 7 or Win XP.

Q: Hi, i wanna purchase your computer together; can you install the software for me before shipping?

A: Yes, our engineer will do this for you if you need.

Q: Hello mate,I just want ask you,Eobd fgtech galletto master 4 is working on windows 7 32 or 64 bit version?

A: Yes, but we suggest customers to use it on windows XP.

Q: Do I need to set the PC time when installing software?

A: It depend what condition you use, if your have some problem, please contact us.

Q: Got my parcel, do you have instruction for installation?? 

A: There is a CD in the package and video guide on our webpage, please check them first.

About installation error:

Q: My FgTech V54 master has Eobd2.exe error?

A: Follow these steps to fix:

1 you need reinstall it double press set up
2 no need delete the FTECH2 V54 software you have install, it will cover the old one

Q: Can Fgtech Galletto V53 be directly updated to Fgtech Galletto V54 and use Fgtech Galletto 4 software?

A: Sorry, it can not update directly. If you want fgtech v54, you need to buy new Fgtech.

Other questions:

Q:Is it possible to order ONLY the cables and Adapters for bdm without the interface?

A: You can order ONLY the cables and Adapters, we will send you the price, please check your email.

Q: In my country, import goods cannot include power adapter, how to solve this problem???

A: We can take the power adapter out of the package, then send it by simple airmail.
original:http://obdtool-co-uk-review.blogspot.com/2015/07/faq-fgtech-galletto-4-v54-mini-ecu.html